Utility

Foundation Flipper 90° +upside/down

mhoUploaded Aug 7, 2026

5Structures
1Buildings
16Downloads
0Likes

Template ID2885Console Guide

Likes: 0

Discord

Description

this places four 90° Foundation around a central Pillar the foundations are turned clockwise & then flipped "nose down" if this is glued to a 90° Foundation, it will give us normal back & even upside-down! (wich means, this tool lets us freely flip back & forth, perfectly aligned!) all these angles can be interconnected & held up with pillars & beams, at any angle! enjoy

How to Get on Console

Full console guide

Console players (PlayStation, Xbox) can download and place this template directly in-game using the Template Hammer Importer mod.

1Install the ModOpen the in-game mod browser and search "Wikily" or "Template Hammer Importer".
2Craft the ImporterGo into Singleplayer + Creative Mode and craft the Wikily Template Importer (1 Fiber).
3Enter Template IDUse the item, enter Template ID 2885 and the building index, then place it.

Buildings1 file

1
Foundation Flipper
5 structures
Template ID: 2885 · Building: 0

Structures5 structures · 2 types

Crafting cost

More from mho

View all

Bases115

round Stone Portal + slim version

A round Stone Portal ...creative name , i know .... This places most sides of a 24sided small wall triangle circle, sunken into the ground to ...well, look fancy ;) >>> to my dismay i must admit, i didnt test this on official, because its such a simple build, BUT ofc official & its dumb "40 pieces in an area-rule" made this a "broken" template & since the game doesnt allow me to give you a fully done portal, i made a SLIM VERSION without pillars !<<< ...sry.... you can ofc snap this to existing foundations, but to get the best look, id say, place this by hand! & build your wall from there, otherwise you might have "holes & such" visible - to get the best result, place this low enough, so that the horizontal pillar-beams just barely dont touch the ground - if placed lower, some of the lowest walls/ceiling/pillars might not autobuild, but the scaffolding exist, so you will be able to build these "missing" pieces by hand, even if the hammer doesnt (the fully build one on the first screen does not use the lowest sides either btw! but, if wanted/placed high enough, you could) - remove all thatch - add the missing horizontal pillars on the ground & those on the outer small walls (if i leave those, the pillars in the circle are blocked for the hammer) [if you use the SLIM VERSION, you have to add all the pillar beams on the inner & outer rim, because wildcard has issues with more then 40+ pieces in an area...] feel free to choose if you want to have foundations in the pathway or not & you could also fill the circles floor itself with small foundations, by offsetting them with a small pillar by 1/4 (as you can see in the screenshot) hope YOU enjoy it

422 Structures
2 Buildings
6 Likes
Vanilla

Decorative95

Round 48 sided Ocean Platform Pool

This places a 48 sided Wall-Ring (+16height offset) over any Ocean Platforms Pool - add a [north turned]Ceiling in the "bottom right corner" (leave the corner itself open) and snap this Template to that ceiling - platforms are basically a giant foundation, so when you place one infront of you, its "north turned"! - the 4 extra foundations place a pillar & beam each (offset by 8 height & 8 distance). these interconnect the ring & the platform on all 4 sides! after removing all thatch, feel free to use the circle however you like! its fully supported/connected to the platform after all! PS: the lonely pillar in the center , only exists as "grab point" for the template (ignore it)! enjoy

355 Structures
9 Likes
Vanilla

Bases81

The Twin-Repli Crafting Oval

This places a small Foundation Oval +16 offset above a normal Floor and adds two half Circles of Dedi's [26], with the Twin-Replicators centered inside the Oval - You can snap this to any existing Foundation Grid, no matter the Height [up to ~3/4 of a wall high] As long as you have a 9x6 Hole in your Foundations & a "North-turned" snap-Point. - If its placed too low for the 90°Foundations, the 2 Failsafe Pillars will create the two 90° Ceilings! so no worries - The Foundations inside the Oval are only Suggestions [at the right height]. if you want to fill it "standalone", use the Triangles on the Outside, otherwise, just "cut" normal Ceilings trough the entire Oval's Foundations, as well as over the 90°ones. - to close this, fill the Dedi half Circles to "3-stacks", then close the Ovals walls & finish it with a rim of quarter Ceilings ontop & you have a standalone Crafting Oval! for the Dedi-Plate Version(wich goes up to 126 dedis): - make sure its placed 5 Steps High and i guarantee you, all will build Flawlessly! - if its too low, the Failsafe Pillars will kick in & build the 90° parts for you, but then you will have to pick up the Cellar-Doors, build Ceilings & Dedis in the Center & then replace the Cellar Doors, on the 90°Beams! (Dedis can not be placed after the Cellar-Doors!) enjoy

200 Structures
2 Buildings
3 Likes
Vanilla

Decorative68

new Stargate

The new Stargate This places a vertical 24sided small-Wall Ring with two Tek Cellar Doors "inside it" (-16 offset) to mimic a "true 9 Chevron Stargate" ! It only took me around 11 Month to get this right again & into an easy instant-build Template, after Wildcard made all "inner-Arches" illegal over the last Year... this one just doesnt use inner Arches at all now & works - just place it low enough that the 2 lowest Pillars in the Ring are ontop/above ground (those 2 will build the entire circle for YOU!) you could place it higher, but then the Gate would start to float, wich looks weird tbh - remove all Thatch get rid of the Ramps & the Scaffolding will just peel off ... the 3 small Foundations just force the Pillars for the CellarDoors & Stairs into existence! - finish the Ring by placing the missing lowest side (Wall, 2 Ceilings & a PillarBeam) these are missing, so this can only build itself correctly! - add a small Stair "in the Back" and cover the Ring's "floor" with 6 small Ceilings [see Screen], so no1 can fall into it & get stuck. Now place the missing Stairs & 2 more down the other Side - Fill the outer Rim with small Pillar Beams (cant leave them in, because of the 40-Piece limit...) - the Triangles on the Sides are only there to cover-up the lower Parts of the CellarDoors, replace them if you want to, or find a better cover-up, they are of no consequence for the circle! Thats it! PS: if you really want to, i guess it could be possible to integrate this into a ceiling floor & have it look like the "round Stone Portal" on ceilings ... its a bit tricky, but the foundation in the front & the stairs in the back, could be used to have this "inside a base", but its not designed for it! [the foundation is just positioned below the cellar door,like on all my gates so far, so the ceilings from the stairs are just "half a wall higher" inside the circle] Enjoy an ancient Alteran Marvel of Engineering in YOUR Base!